KENWOOD DMCK3
Instrukcja Serwisowa

DMC-K3
CONTENTS / ACCESSORIES
Contents
SPECIFICATIONS .........................................Top cover CONTENTS / ACCESSORIES ....................................2 CONTROLS .................................................................3 DISASSEMBLY FOR REPAIR.....................................4 CIRCUIT DESCRIPTION .............................................5 PC BOARD ..................................................................9 SCHEMATIC DIAGRAM ............................................11 EXPLODED VIEW .....................................................15 PARTS LIST...............................................................17

Accessories
AC adapter (1) * (W09-) Batteries : NB150 (1) (W09-1267-05) Carrying case (1) (W01-0938-05) Stereo headphone (1) * (W01-0963-05)

Remotcon (1) (A70-1258-05)

Stereo headphone (1) * (W01-)

* Refer to parts list on page 17.

Caution

Troubleshooting
Symptom Cause Remedy ÷ Close disc holder securely. ÷ Charge the battery. ÷ Deactivate HOLD status. ÷ Increase the volume. ÷ Insert plug securely. ÷ Deactivate HOLD status. ÷ Charge the battery. ÷ Insert plug securely. ÷ Close disc holder securely. ÷ Replace the MD. ÷ Move the unit to a place where there is little vibration or set to �PS off�. ÷ Use the special rechargeable battery (NB-150) ÷ Wait until the unit has cooled to normal temperature. ÷ Use the accessory AC adaptor. Unit fails to ÷ The disc holder is not securely turn ON. closed. ÷ The battery is depleted. ÷ HOLD status is engaged. There is no ÷ The volume is at minimum sound. level. ÷ The remote control or headphones are disconnected. The unit does ÷ HOLD status is engaged. not respond ÷ The battery is depleted. to key opera- ÷ The remote control or headtion. phone plug is not securely inserted. ÷ The disc holder is not securely closed. Sound skips. ÷ The disc is scratched or damaged or the recording is not good. ÷ The unit is in a place where there is excessive vibration.

Beware of condensation
When water vapor comes into contact with the surface of cold material, water drops are produced. If condensation occurs, correct operation may not be possible, or the unit may not function correctly. This is not a malfunction, however, and the unit should be dried. (To do this, turn the POWER switch ON and leave the unit as it is for several hours.) Be especially careful in the following conditions: � When the unit is brought from a cold place to warm place, and there is a large temperature difference. � When a heater starts operating. � When the unit is brought from an air-conditioned place to a place of high temperature with high humidity. � When there is a large difference between the internal temperature of the unit and the ambient temperature, or in conditions where condensation occurs easily.

Resetting the unit
This system uses a microcomputer so it may malfunction due to external noise or interference. In such a case, unplug the power cord and remove the batteries, then plug the power cord again and insert the batteries again.

Battery does ÷ You are using commercial renot charge. chargeable battery. ÷ The unit has become hot because of exposure to direct sunlight etc. ÷ You are using another AC adaptor than the accessory adaptor. ÷ The AC adaptors has become ÷ Connect the AC adaptor disconnected. securely.

Meaning of display messages
Message �noDISC� �BLANK � Meaning Action ÷ There is no MD in the unit. ÷ Insert a MD into the unit. ÷ Nothing is recorded on this ÷ Replace the disc with a MD. prerecorded MD when playing it back. ÷ The *UTOC contents are ÷ Replace the MD. faulty. ÷ The disc is scratched or dam- ÷ Replace the MD. aged, so playback is not possible.

�ERROR �

2

*UTOC: A recordable MD has an area for recording so-called UTOC (User's Table of Contents) data. The UTOC contains number of tracks, playing time, written data, and other rewritable information.